manualshive.com logo in svg

Interactive Technologies Commander 2000, Owner'S Manual, Page: 41 / 61

Share
Download
Interactive Technologies Commander 2000 Owner'S Manual Download Page 41

41

Replacing Panel Backup Batteries

Your panel uses six NiCd or alkaline backup batteries in case of an AC power failure. The 
actual length of time the panel will operate on backup batteries depends on your backup 
power time setting, the type of batteries used, and the condition of the batteries. The 
default setting for backup power is 5 hours and may be changed by your security consult-
ant.

Test your backup batteries weekly by checking the system status, as described in the sec-
tion "Required System Tests" on page 39. If the panel announces, 

System battery failure

 

when you check system status, replace your batteries.

Table 9

. How to Activate Sensors During Sensor Test

Sensor

 

‡

Action

Door/Window

Open the secured door or window, and reclose it 
after it beeps.

Freeze

Apply ice or freeze spray to the sensor for about 45 
seconds. Do not let the sensor get wet.

Glass Guard 

†

Motion Sensor

Avoid sensor’s view for 5 minutes, then enter its 
view.

Emergency But-

tons on Touchpads 

and Panel

Press and hold the appropriate emergency but-
ton(s) for at least 3 seconds. Test all three emer-
gency buttons (

POLICE, FIRE, AUXILIARY

).

Rate-of-Rise

Rub your hands together until warm, then place 
one hand on the sensor for 30 seconds.

Shock 

†

Smoke

Press and hold the test button until the system 
sounds transmission beeps.

Water-Resistant 

Pendant Panic 

Sensor

Press the button on the sensor.

† 

You cannot test this sensor. Your security consultant should test the sensor 

periodically.

‡

 Your security consultant can explain how to test any additional sensors used 

with your system.

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for Commander 2000






























































Reviews:

No comments