manualshive.com logo in svg

Interactive Technologies Commander 2000, Owner'S Manual, Page: 36 / 61

Share
Download
Interactive Technologies Commander 2000 Owner'S Manual Download Page 36

36

Table 7 shows a few system status messages that may be announced.

Checking for Alarms

The panel saves a record of any alarms that occurred while the system was armed. Use the 
following procedures to review any alarm messages stored in memory and clear the alarm 
memory when you no longer need the alarm messages.

■

To hear alarms in panel memory:

Enter 

C STATUS.

The panel announces, 

Sensor [sensor #]

 

[alarm type]

 

Alarm Memory

. If no alarms 

occurred during the arming period, the panel announces, 

Alarm Memory is OK

.

■

To clear alarm memory:

1.

Enter any 

ACCESS CODE + 9.

The panel and interior sirens sound one long beep and the panel announces, 

Sensor 

test is ON.

2.

Enter any 

ACCESS CODE + 1 

to exit out of sensor test.

The panel announces, 

Alarm system is OFF.

 The alarm memory is now empty.

Table 7

. Status Voice Messages and Their Meanings

Voice Message

Meaning

Alarm system is OFF, system battery is OK, 
AC power is OK.

All sensors are closed, no system problems exist, 
and system is in level 1.

Alarm system is OFF, sensor [sensor #] 
open.

A perimeter sensor is open. Close or bypass sen-
sor to arm system.

Alarm system is OFF, sensor [sensor #] low 
battery.

A sensor has a low battery. Contact your security 
consultant for sensor battery replacement.

Alarm system is ON level 3, sensor [sensor 
#] bypassed.

All sensors are armed except for the announced 
sensor.

Alarm system is OFF, sensor [sensor #] trou-
ble.

Sensor cover is off. Put sensor cover on, then 
activate the sensor. For example, on a motion sen-
sor, walk through its range of coverage.

Invalid, try again.

An incorrect or incomplete command was entered 
at the panel or from a touchpad.

Alarm system is OFF, sensor [sensor #] fail-
ure.

A sensor isn’t working. Contact your security 
consultant.

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for Commander 2000






























































Reviews:

No comments