manualshive.com logo in svg

Interactive Technologies Commander 2000, Owner'S Manual, Page: 22 / 61

Share
Download
Interactive Technologies Commander 2000 Owner'S Manual Download Page 22

22

NOTE:

Depending on programming, a Keychain Touchpad may 
arm your system to the next higher arming level or directly 
to level 3 NO DELAY.

4.

Exit the premises within the delay time, if you are leaving.

When the delay time expires, the panel and interior sirens sound two or three 
more beeps. If you are still on the premises and want to leave, disarm and 
rearm the system to prevent an accidental alarm.

■

To arm the system using a Magic Key:

1.

Close all perimeter doors and windows.

2.

Check to see that the panel’s READY light is on or blinking.

If the READY light is still not on or blinking, check all perimeter doors and 
windows again to make sure they are closed. If the READY light is still not 
on or blinking, see “Bypassing Normally Armed Sensors (BYPASS)” on 
page 28.

3.

Insert the Magic Key into the panel key slot (see Figure 3).

NOTE:

The Magic Key rearms the system to its previous arming 
level (level 2 or 3). See "Using and Programming the Magic 
Key" on page 31 for more information.

4.

Hold the Magic Key steady in the slot until the panel and interior sirens 
sound arming level beeps, and the panel announces, 

Alarm system is ON 

[level 2 

or

 3].

5.

Exit the premises within the delay time, if you are leaving.

When the delay time expires, the panel and interior sirens sound arming 
level beeps again. If you are still in the premises and want to leave, disarm 
and rearm the system to prevent an accidental alarm.

Activating Emergency Alarms

The emergency buttons on the panel or touchpads allow you to activate the appropriate 
emergency alarm. Table 4 is a comparison of the alarms that indicates how you can use the 
panel and touchpads to activate each alarm and how you can expect your security system 
to respond to them.

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for Commander 2000






























































Reviews:

No comments