manualshive.com logo in svg

Interactive Technologies Commander 2000, Owner'S Manual, Page: 28 / 61

Share
Download
Interactive Technologies Commander 2000 Owner'S Manual Download Page 28

28

3.

Press the Arm button, then press the Star button and hold until the light blinks.

The Panel’s STAY or AWAY light turns on, and the Panel and interior sirens sound 
arming level beeps. The NO DELAY light turns on, and the Panel and interior sirens 
sound arming level beeps again.

NOTE:

Disarm the system before opening a perimeter door or window, or 
an accidental alarm may occur.

NOTE:

Depending on programming, a Keychain Touchpad may arm 
your system to the next higher arming level, or directly to level 3 
NO DELAY.

Bypassing Normally Armed Sensors 
(BYPASS)

Use the Bypass feature to ignore selected sensors, so they can remain open or so they can 
be opened and closed without sending an alarm. Bypassing a window sensor allows you to 
leave the window open while the system is armed. Bypass also allows you to ignore a sen-
sor that is not working properly and is causing unwanted alarms. You can bypass all sen-
sors for any security level in which they are active, except smoke, heat, and fire pull 
sensors. Bypassed sensors remain bypassed until you change security levels. 

You can bypass sensors indirectly or directly. Indirect bypassing lets you bypass open sen-
sors when the system will not arm. Direct Bypass lets you bypass sensors when the system 
is armed and operating normally.

■

To bypass sensors indirectly:

1.

Arm the system. If the panel announces, 

Sensor [sensor #] open

 and sounds protest 

beeps, continue to step 2.

If the panel arms successfully, you do not have to bypass any sensors.

2.

Press 

BYPASS.

The panel announces, 

Alarm system is ON [level #]. Sensor [sensor #] bypassed

.

NOTE:

The indirect bypass procedure shall not be used in UL listed installa-
tions.

NOTE:

The indirect bypass procedure does not work when you arm the 
panel by pressing the COMMAND button rather than entering your 
access code.

■

To bypass sensors indirectly from a Keychain Touchpad:

1.

Press the Arm button. If the panel announces, 

Sensor [sensor #] open

 and sounds a 

two-beep continuous sequence (1 long, 1 short), continue to step 2.
If the panel arms successfully, you do not have to bypass any sensors.

BYPASS

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for Commander 2000






























































Reviews:

No comments