manualshive.com logo in svg

Interactive Technologies Commander 2000, Owner'S Manual, Page: 23 / 61

Share
Download
Interactive Technologies Commander 2000 Owner'S Manual Download Page 23

23

Police, Fire, and Auxiliary/Medical Alarms

Use the 

POLICE, FIRE,

 or 

AUXILIARY 

alarm buttons in an emergency.

A police alarm activates interior and exterior sirens and sends a police alarm to 
your monitoring service. The monitoring service should contact the police.

A fire alarm activates interior and exterior sirens and sends a fire alarm to your 
monitoring service. The monitoring service should contact the fire department.

An auxiliary/medical alarm activates interior sirens and sends an auxiliary/medi-
cal alarm to your monitoring service. The 

AUXILIARY

 button can be used to 

request either auxiliary or medical service, if the monitoring service knows in 
advance what service to contact in case of an alarm.

Table 4

. A comparison of the alarm types

Where you can activate the 

alarm

What the alarm activates

Alarm type

From 

the

panel

From a

Handheld

Touchpad

From a

Keychain

Touchpad

Interior

sirens

Exterior

sirens

Monitoring 

service 

action

POLICE

Yes

Yes

*

Yes

Yes

Police alarm

FIRE

Yes

No

*

Yes

Yes

Fire alarm

AUXILIARY/
MEDICAL

Yes

Yes

*

Yes

No

Pre-specified 
instructions

SILENT 
DURESS

Yes

No

*

No

No

Police alarm

* Must be programmed by your security consultant

POLICE

FIRE

AUXILIARY

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for Commander 2000






























































Reviews:

No comments