79
En
Appendix
Troubleshooting
If you have any trouble using the AV receiver, look for a
solution in this section. If you can’t resolve the issue
yourself, contact the dealer from whom you purchased this
unit.
■
Can’t turn on the AV receiver
■
The AV receiver turns off unexpectedly
■
When the power is restored after a power
interruption, “CHECK SP WIRE” appears on the
display
■
There’s no sound, or it’s very quiet
If you can’t resolve the issue yourself, try resetting the
AV receiver before contacting the dealer from whom
you purchased this unit.
To reset the AV receiver to its factory defaults, turn
it on and, while holding down
VCR/DVR
, press
8
On/Standby
. “Clear” will appear on the display
and the AV receiver will enter standby mode.
Note that resetting the AV receiver will delete your
radio presets and custom settings.
To reset the remote controller to its factory defaults,
while holding down
Receiver
, press and hold down
Home
until
Receiver
button lights (about 3 seconds).
Within 30 seconds, press
Receiver
again.
The on-screen menus appear only on a TV that is
connected to the
HDMI OUT MAIN
. If your TV is
connected to other video outputs, use the AV
receiver’s display when changing settings.
Power
Make sure that the power cord is properly plugged
into the wall outlet.
—
Unplug the power cord from the wall outlet, wait
five seconds or more, then plug it in again.
—
The AV receiver will automatically enter standby
mode when Auto Standby has been set and launches.
61
Home
Receiver
The protection circuit has been activated. Remove
the power cord from the wall outlet immediately.
Disconnect all speaker cables and input sources, and
leave the AV receiver with its power cord
disconnected for 1 hour. After that, reconnect the
power cord and set the volume to maximum. If the
AV receiver stays on, set the volume to minimum,
disconnect the power cord, and reconnect your
speakers and input sources. If the AV receiver turns
off when you set the volume to maximum,
disconnect the power cord, and contact the dealer
from whom you purchased this unit.
—
Audio
Make sure that the digital input source is selected
properly.
46
Make sure that all audio connecting plugs are pushed
in all the way.
16
Make sure that the inputs and outputs of all
components are connected properly.
17
-
20
Make sure that the polarity of the speaker cables is
correct, and that the bare wires are in contact with
the metal part of each speaker terminal.
13
Make sure that the input source is properly selected.
23
Make sure that the speaker cables are not shorting.
13
Check the volume. The AV receiver is designed for
home theater enjoyment. It has a wide volume range,
allowing precise adjustment.
—
If the
MUTING
indicator is flashing on the display,
press the remote controller’s
Muting
to unmute the
AV receiver.
41
While a pair of headphones is connected to the
Phones
jack, no sound is output from the speakers.
41
If there’s no sound from a DVD player connected to
an HDMI IN, check the DVD player’s output
settings, and be sure to select a supported audio
format.
—
Check the digital audio output setting on the
connected device. On some game consoles, such as
those that support DVD, the default setting is off.
—
With some DVD-Video discs, you need to select an
audio output format from a menu.
—
If your turntable uses an MC cartridge, you must
connect an MC head amp, or an MC transformer.
—
Make sure that none of the connecting cables are
bent, twisted, or damaged.
—
Not all listening modes use all speakers.
35
Specify the speaker distances and adjust the
individual speaker levels.
48
Make sure that the speaker setup microphone is not
still connected.
—
The input signal format is set to “
PCM
” or “
DTS
”.
Set it to “
Off
”.
57
Summary of Contents for DTR-50.3
Page 1: ...AV Receiver DTR 50 3 Instruction Manual...
Page 99: ...99 En Memo...