Ingersoll-Rand ARO EVO EP20 Series Operator'S Manual Download Page 36

Page: 36 / 44

Page 36 of 44

EP20-XXXXX-XXX-XXX (en)

PARTS LIST / OIL FILTER EP20-XXXXX-XXX-XXX

151

149

179

150

SEE DETAIL C

128

129

177

174

301

302

173

176

175

171

172

176

178

155

153

166

167

170

169

168

159

167

166

170

169

168

156

160

152

157
154

162

163

161

DETAIL C

NOTE: DO NOT OVERTIGHTEN FASTENERS.

ASSEMBLY TORQUE REQUIREMENTS

(129, 176) Straight Thread O-Ring, tighten to

20-25 ft lbs (27-34 Nm)

(150) Screws, tighten to 8-12 ft lbs (11-16 Nm)

(174, 175) Screws, tighten to 20-30 in lbs (2.2-3.4 Nm)

(158) Plug, tighten to 45-50 ft lbs (61-68 Nm)

(179) Fitting Body, tighten to 45-50 ft lbs (61-68 Nm)

158

165

183

185

126

127

189

188

184

181

182

187

NOTE

: Items shown in crankcase parts

list on page 32.

Figure 17

Summary of Contents for ARO EVO EP20 Series













































Search results

Summary of Contents for ARO EVO EP20 Series

Reviews:

Brands by name

Popular brands

Ingersoll-Rand ARO EVO EP20 Series, Operator'S Manual

Search results

Summary of Contents for ARO EVO EP20 Series

Reviews:

Brands by name

Popular brands