Ingenico iCT2XX Operating Manual Download Page 70

Page: 70 / 147

SKYZER TECHNOLOGIES

PAGE 70 OF 147

INGENICO ICT2XX PTS2018 PAYMARK OPERATING MANUAL

Version 1.00

9.3 Pure Commerce CSE Configuration

Step

Terminal Display

Comment

1.0

Press

FUNC

2.0

FUNCTION?

Enter

3025703

and press

ENTER.

3.0

CONFIG PARAMS?
ENTER OR CLEAR

ENTER

to configure the parameters or

CLEAR

to cancel and exit to idle prompt.

4.0

TERMINAL ID?
XXXXXXXX

This parameter specifies the Pure Commerce CSE Terminal ID assigned by Pure
Commerce.

By default the BNZ CSE terminal ID will be same as the

Paymark terminal ID

5.0

MERCHANT ID?
XXXXXXXXXXX

This parameter specifies the DCC Merchant ID assigned by Pure Commerce.

default the Pure Commerce CSE merchant ID will be same as the Paymark
Merchant ID

6.0

PRIMARY

HOST PORT

6880

This parameter specifies the Primary Host Port for Pure Commerce CSE. Press

ENTER.

Be default it is set to 6880

7.0

SECONDARY
HOST PORT

6880

This parameter specifies the Secondary Host Port for Pure Commerce CSE. Press

ENTER.

By default it is set to 6880

8.0

RATE SERVER

HOST DNS

www.currencyselect

.bnz.co.nz

This parameter specifies the Rate Server Host DNS for Pure Commerce CSE. Press

ENTER.

By Default it is set to www.currencyselect.bnz.co.nz

9.0

RATE SERVER

HOST DNS

bnz.pure-

commerce.com

This parameter specifies the Rate Server Host DNS for Pure Commerce CSE. Press

ENTER.

By default it is set to bnz.pure-commerce.com

10.0

USER NAME
skzyerprod01

A default username has been preset for Skyzer terminals

By default it is set to skzyerprod01

11.0

PASSWORD
**********

The default password is preset to x79F0vQh

Summary of Contents for iCT2XX




















































































































































Search results

Summary of Contents for iCT2XX

Reviews:

Related manuals for iCT2XX

Brands by name

Popular brands

Ingenico iCT2XX, Operating Manual

Search results

Summary of Contents for iCT2XX

Reviews:

Related manuals for iCT2XX

Brands by name

Popular brands