5
Maximum Frame
Rate
30fps@1280
×
960 30fps@1280
×
720
Data Rate
Variable bit rate;
Constant bit rate: 256Kbps~10000Kbps (Major
stream); 256Kbps~2000Kbps (Minor stream)
Motion Detection
Up to 4 areas
Privacy Mask
Up to 4 masks
ROI
4
Local Recording
Available
Upgrade Online
Available
Password
Protection
Available
Network Port
One RJ45 10/100M self-adaptive Ethernet port
Analog Video
Output
Available via BNC port
Applicable
Protocols
IPv4, TCP, UDP, IGMP, DHCP, FTP, SNMP (V3),
SMTP, NTP, RTP, RTSP, RTCP, HTTP, HTTPS, TSL,
SSL, 802.1X, Qos, PPPoE, DNS, ARP, ICMP
Power Supply
12VDC
Power
Consumption
＜
5W
Operating
Temperature
14°F~122°F (-10°C~+50°C)
Storage
Temperature
-4° F ~ 140° F (-20° C ~ 60° C)
Operating
Humidity
0%-90% RH (non-condensing)
Dimensions (H×Ø)
3.34"×4.71" (84.7mm×119.5mm)
Box Dimensions
(L×W×H)
6.65 "×6.65 "×5.79" (169mm×169mm×147mm)
6
Unit Weight
1.43lbs. (0.65kg)
Shipping Weight
1.83lbs. (0.83kg)
1.6 Precautions
1.
Do not drop the camera or subject it to strong knock.
2.
Do not point the camera lens toward the sun or other strong light.
3.
Do not install the camera in environment with temperature beyond the
acceptable range (from -10°C to 50°C).
4.
Never let liquid of any kind flow into this unit.
5.
Do not directly touch the CMOS element. If it is necessary to clean the
element, use a soft cloth moistened with alcohol to wipe off the dust.
6.
If any abnormality occurs, make sure to unplug the unit and contact your
local dealer.
7.
This camera features AGC circuit, so when the camera is applied under
low illumination, sensitivity will enhance automatically, making images
look rough, which is normal.
8.
The camera power supply is 12VDC. Be sure of the +/- terminal correct.
9.
Firstly perform network settings after login. Gateway IP address should be
set to the IP address of the gateway that the device connects to.
10.
The IP address is not allowed to conflict with that of other devices;
otherwise, you cannot visit the camera.
7
CHAPTER II INSTALLATION
Step 1: Prepare mounting holes
Attach the enclosed mounting schematic label on the desired position of wall
or ceiling; drill holes according to the label’s instruction (4 mounting holes
and 1 cable hole).
Figure 2-1
Step 2: Install camera base
Unscrew the base and take it off. Install the base to the ceiling via the 4
mounting holes.
Figure 2-2
8
Step 3: Pre-fasten minidome camera
Install tightening ring, chuck ring and dome module to the base. Keep tightening
ring loose, so that the dome module can turn freely.
Tightening ring
Chuck ring
Dome module
Figure 2-3
Step 4: Adjust dome module
1.
Turn the dome module to make it point to surveillance area. The
camera features X, Y, Z 3-axis adjustment. It allows 0°~360° panning
adjustment,
-75°~75°
tilting adjustment and 0°~360° rotating
adjustment.
2.
Adjust the lens according to the schematic label; make sure
photosensitive resistance lies at the bottom; then fasten
tightening ring.
Photosensitive resistance
Keep the arrowhead up
when mounting.
Figure 2-4
