Infinova V2117 Installation & Operation Instructions Download Page 28

Page: 28 / 32

Non-PTZ Mode

Keyboard Key

NVR Function

[FAR/

]

Under non-PTZ status, switch among multiple images when previewing them.

Note: Divide the screen into 1/4/9/16 screens, but into 8 screens.

Joystick Up

Select upwards within a control.

Joystick Down

Select downwards within a control.

Joystick Left

Select leftwards within a control.

Joystick Right

Select rightwards within a control.

[ACK/ENTER]

Confirm the current operation.

[ARM/POWER]

After the host is connected to power supply, press it to power on the device/ press and hold for 10 seconds to

power off the device.

[F1]

In a menu interface, move the cursor backwards.

[F2]

In a menu interface, move the cursor backwards.

[USER] Reserved.

[SITE] Reserved.

PTZ Mode

Keyboard Key

NVR Function

[CLEAR/ESC]

Exit the current interface.

[NEAR/*]

Under PTZ mode, it means “focal ”.

[TELE/PTT]

Under PTZ mode, it means “zoom +”.

[SHOT/PRST] (OPER position)

Under PTZ mode, call a preset.

[CLOSE/PTZ]

Enable PTZ mode.

[WIDE/SYS]

Under PTZ mode, it means “zoom -”.

[FAR/

]

Under PTZ mode, it means “focal length -”.

Joystick Up

Under PTZ mode, turn the pan/tilt upwards.

Joystick Down

Under PTZ mode, turn the pan/tilt downwards.

Joystick Left

Under PTZ mode, turn the pan/tilt leftwards.

Joystick Right

Under PTZ mode, turn the pan/tilt rightwards.

[F1]

Decrease PTZ step size.

[F2]

Increase PTZ step size.

[SHOT/PRST] (PROG position)

Under PTZ mode, set a preset.

91+ [SHOT/PRST] (PROG position)

Under PTZ mode, set/save autopan 1.

91+ [SHOT/PRST] (OPER position)

U nder PTZ mode, call autopan 1.

Numeric key+ [RUN]+ [ACK]

Under PTZ mode, perform tour.

Note: Press [1]+ [RUN]+ [ACK] to call automatic cruise PATH2.

34+ [SHOT/PRST] (OPER position)

Under PTZ mode, home automatically.

99+ [SHOT/PRST] (OPER position)

Under PTZ mode, scan automatically.

92+ [SHOT/PRST] (PROG position)

Under PTZ mode, set/save autopan 2.

92+ [SHOT/PRST] (OPER position)

Under PTZ mode, call autopan 2.

93+ [SHOT/PRST] (PROG position)

Under PTZ mode, set/save autopan 3.

93+ [SHOT/PRST] (OPER position)

Under PTZ mode, call autopan 3.

Summary of Contents for V2117

































Search results

Summary of Contents for V2117

Reviews:

Related manuals for V2117

Brands by name

Popular brands

Infinova V2117, Installation & Operation Instructions

Search results

Summary of Contents for V2117

Reviews:

Related manuals for V2117

Brands by name

Popular brands