8
address. If the remote site IP address is 192.168.2.219, the SITE will
display 219. MON displays monitor number in 3 digits; CAM
displays camera number in 4 digits. @N (@Y) indicates network
connection status. @Y indicates connected; @N indicates
disconnected. If the network is disconnected, SITE displays
nothing.
At 8-digit camera number display mode, the LCD will display as
follows:
MON:001
CAM:00012345
S@Y:219
Of which, S@Y (S@N) indicates network connection status. S@Y
indicates connected, and displays the end section of the remote site
IP address. If the remote site IP address is 192.168.2.219, then it
will display S@Y:219. S@N indicates disconnected, and no IP
address is displayed.
MON displays monitor number; and CAM displays camera number
in 8 digits.
Note:
If the camera number is less than 5 digits, the LCD will
display as follows:
MON:001
CAM: 1234
S@Y:219
At 12-digit camera number display mode, the LCD will display as
follows:
M:001
C: 111111111111
S@N
Of which, S@Y (S@N) indicates network connection status. S@Y
indicates connected, and displays the end section of the remote site
IP address. If the remote site IP address is 192.168.2.219, then it
will display S@Y:219. S@N indicates disconnected, and no IP
address is displayed.
“M” displays monitor number; and “C” displays camera number in
12 digits.
3. At DVR RS485 Control Mode
UNIT
PTZ
229
OFF
UNIT indicates DVR number.
PTZ indicates PTZ status. Options are OFF and ON. The PTZ
function can be enabled by CLOSE key and disabled by CLEAR
key.
To change DVR number, press the “MON/UNIT” key on the
keyboard, and the UNIT on the LCD will flash. Then enter the
desired number on the keyboard, such as 89:
UNIT
PTZ
229
OFF
89
And then press “MON/UNIT” key again. The LCD will display as
follows:
UNIT
PTZ
089
OFF
4. At DVR/NVR Ethernet Control Mode
UNIT
PTZ
229
OFF
@Y
UNIT indicates DVR/NVR number.
PTZ indicates PTZ status. Options are OFF and ON. The PTZ
function can be enabled by CLOSE key and disabled by CLEAR
key.
@N (@Y) indicates network connection status. @Y indicates
connected; @N indicates disconnected.
Note:
Network connection status is effective for controlling DVRs
via Ethernet. When controlling NVR, the status can be @N or @Y.
3.1.2 Establishing Ethernet Communication
To establish the communication between V2117 keyboard and
Infinova series matrix switcher/controller systems via Ethernet
network, simply route the Ethernet port on the rear panel of V2117
via Hub to the Ethernet port on the matrix switching system. See
figure 2-7 for your information.
3.1.3 User Login
As a system security feature, certain matrix models, V2040 for
example, requires a User Login procedure to access system
functions. Under such circumstances, you will be prompted by a
"
UC.
" message on the LCD to enter a valid user number, and then a
"
PSC
" message to enter the pass code. Only by entering a valid user
number and its pass code can you access the keyboard functions
such as video switching and menu programming.
To login the system,
1.
Enter the user number on the numeric keypad.
2.
Press the ACK key. The message "
PSC
" will be displayed on the
LCD.
3.
Enter the pass code (up to 6 digits) for the user. To clear an
incorrect entry, press the CLEAR key, and enter the correct code.
4.
Press the ACK key to confirm. If the "
PSC
" message has been
cleared from the LCD, it indicates a successful login, i.e., the user
has been authorized to perform system operation on the keyboard.