15
Communication ports on back of V2117
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
VIDEO OUT
LINE IN
AUDIO OUT
VGA
KEYBOARD
RS-232
RS-485
ETHERNET
VIDEO IN
LOOPING
AUDIO IN
AUDIO IN
1
2
Tested To Comply With
FCC Class B Standard
For Home Or Office Use
230V
110V 60Hz
50Hz
USB
3
G
2
G
G
4
G
1
RELAYS
G
6
7 8
1
2 3 4
5
0
ALARMS
14 15 16
9
10 11 12 13
ALARMS
G
V3010
BL
OR
BK
RD
WH
BR
YL
GR
T+T-G
B W S
ETHERNET
RS232
ETHERNET
RS232/RS485
PROTOCOL SELECT
BAUD
POWER
O
N
1
2
3
4
5
6
7
8
O
N
1
2
3
4
-
+
12VDC 500mA
Hub
1 8
T+
T-
V2415
V2117
LAST
LOCK
ACK
ENTER
NEXT
RUN
PLAY
HOLD
REC
OFF
ARM
POWER
SALVO
MENU
PATRN SHOT
PRST
PROG
1
2
3
4
5
6
7
8
9
CAM
0
MON
UNIT
F 1
CLEAR
ESC
F 2
MENU
PROGRAM
OPERATE
CLOSE
PTZ
OPEN
EDIT
OFF
ON
FAR
WIDE
SYS
TELE
PTT
USER
SITE
CONTROL
UP
DOWN
L
R
NEAR
AUXILIARY
IRIS
FOCUS
ZOOM
P
A
G
E
P
A
G
E
P
A
G
E
P
A
G
E
E
N
T
E
R
E
X
I
T
SYSTEM KEYBOARD
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
SHIFT
POWER
MANCHESTER
RS485
ETHERNET
Infinova
R
ETHERNET Cable
Figure 4-2. Typical connection
4.4.1 Keyboard Menu Setup
1.
Press PROG key to enter the “COMM Setup” menu, and Press
PROG key again after the “COMM Setup” option is displayed.
Then press ACK key to select “Ethernet” option and press ACK
to confirm.
2.
Select “Ethernet IP Setup” and press PROG to enter the option.
Configure local IP address and then press NEXT key to select
and configure DVR IP address. Then, configure the relevant
gateway and subnet mask.
After the system is correctly connected and configured, place the
key switch at the OPERATE position, and the LCD on the keyboard
will show the following information:
UNIT
PTZ @ N
000
OFF
If the keyboard and DVR communicate normally, the LCD on the
keyboard will show “@Y”.
Please refer to
section 4.3
for details about system operations.
Note:
Please refer to V2415 Manual for details about V2415
configurations.
Chapter V NVR Control Function
The above sections describe the basic functions and common
operation of the V2117 series keyboards. To enable a V2217
keyboard to control a network video recorders (NVR), realizing the
same control function as that of the front-panel keys of an NVR,
you may set the menu of the V2117 keyboard to enable switch
between common functions and NVR controlling function. For
details of NVR control, please read this section.
5.1 System Setting
Before using a V2117 keyboard to control an NVR, you need to set
the menu of the keyboard.
5.1.1 Enter System Setting Mode
Toggle the Key switch to MENU position, and press F1 key to enter
the first-level menu. The LCD screen displays:
System Keyboard
VXXX
Note:
The “XXX” is keyboard version NO., which is a number.
Press PROG key to enter
“System Setup”
menu.
In
“System Setup”
menu has 8 options, from which you may press
NEXT or LAST to choose.
COMM Setup
(communication protocol setting)
RS485 Setup
(RS485 setting)
BWS Setup
(BWS setting)
Joystick Setup
(3D joystick setting)
RPT Setup
(RPT setting)
Beeper Setup
(beeper setting)
Cam Input Setup
(CAM input mode setting)
Factory Default
(factory default)
5.1.2 Set Keyboard Menu
1.
Press PROG key to enter the
“COMM Setup”
menu. When
“COMM Select”
is displayed, press PROG key again, press
ACK key and select
“Ethernet”
, and then press PROG key
to confirm.
2.
Choose
“Ethernet”
, press PROG key, set a multicast IP
address, which is 224.0.0.52 by default.
Note:
The IP address should be identical with the multicast IP
address of a network keyboard in the NVR.
5.2 System Connection
Here we take a V2117 keyboard and Infinova V3072-32K as
examples to describe the connection.
Use a network cable to connect the network interface of the
keyboard and the network interface on the rear panel of the
V3072-32K.
The connection is shown as below.