industrie technik TH-xxxSx1 Series User Manual Download Page 117 | Manualshive

Page: 117 / 126

background image

117/126

• BACnet signals

Analogue inputs

Object name

Object-ID

Description

Unit

Writable

INT_TEMP_COMP

ANALOG_INPUT:3002

Internal sensor temperature

°C / °F

No

TEMP_AI1

ANALOG_INPUT:3003

Remote sensor 1 temperature

°C / °F

No

TEMP_AI2

ANALOG_INPUT:3004

Remote sensor 2 temperature

°C / °F

No

INPUT_AI3

ANALOG_INPUT:3005

Remote sensor 3

°C / °F

ppm

%r.h.

No

INT_HUM_COMP

ANALOG_INPUT:3006

Internal humidity

%r.h.

No

If a temperature sensor is broken, the temperature visualized corresponds to values indicated on the table below:

Temperature of sensor with unit in °C (

I45

=0)

Value in °C

Sensor open

-20.0°C

Sensor with short-circuit

97.0°C

Temperature of sensor with unit in °F (

I45

=1)

Value in °F

Sensor open

-4.0°F

Sensor with short-circuit

206.6°F

For INPUT_AI3 set as 0...10V, if voltage in input is upper then 13.5V, the value 32000 indicating out of scale is put on Present_Value if RANGE_MAX_VOLT_

INPUT (Present_Value) - RANGE_MIN_VOLT_INPUT (Present_Value) is upper than 399, otherwise the value 3200 indicates out of scale.

Analogue values

Object name

Object-ID

Description

Unit

Writable

OUT_A

ANALOG_VALUE:3012 Value of output AO1

V

No

OUT_B

ANALOG_VALUE:3013 Value of output AO2

V

No

OUT_C

ANALOG_VALUE:3014 Value of output AO3

V

No

WORKING_TEMP

ANALOG_VALUE:3015 Operating temperature

°C / °F

No

WORKING_SET

(Note 1)

ANALOG_VALUE:3016 Operating setpoint

°C / °F

No

TOTAL_HOUR_OF_FAN

ANALOG_VALUE:3024 Number of hours of operation of fan

h

No

COR_INT_TEMP

(Note 3)

ANALOG_VALUE:2132 Internal temperature correction

°C / °F

Yes

COR_INT_HUM

ANALOG_VALUE:2133 Measured internal humidity correction

%r.h.

Yes

COR_REM_AI1

(Note 3)

ANALOG_VALUE:2134

External temperature correction AI1

°C / °F

Yes

COR_REM_AI2

(Note 3)

ANALOG_VALUE:2135

External temperature correction AI2

°C / °F

Yes

COR_REM_AI3

(Note 3)

ANALOG_VALUE:2136

External temperature correction AI3

°C / °F

Yes

WEIGHT_REM_AIR

ANALOG_VALUE:2137

Weighting (%) of external sensor AI1 in relation to the

internal sensor

%

Yes

ECO_SET_ADJUST

(Note 2)

ANALOG_VALUE:2143 Economy offset

°C / °F

Yes

HOL_SET_ADJUST

(Note 2)

ANALOG_VALUE:2144 “Not occupied holiday” mode offset

°C / °F

Yes

BASIC_ANTIFROST_SET

(Note 2)

ANALOG_VALUE:2145 Frost protection setpoint

°C / °F

Yes

WINTER_SET_CHANGEOVER

(Note 2)

ANALOG_VALUE:2146 Heating setpoint for automatic season changeover sensor

°C / °F

Yes

SUMMER_SET_CHANGEOVER

(Note 2)

ANALOG_VALUE:2147 Cooling setpoint for automatic season changeover sensor

°C / °F

Yes

SET_MIN_THERM

(Note 2)

ANALOG_VALUE:2148 Minimum thermostat setpoint

°C / °F

Yes

BASIC_HEAT_SET

(Note 2)

ANALOG_VALUE:2138 Heating setpoint for regulation other than 4 pipe system

°C / °F

Yes

BASIC_COOL_SET

(Note 2)

ANALOG_VALUE:2139 Cooling setpoint for regulation other than 4 pipe system

°C / °F

Yes

BASIC_SET_4_PIPE

(Note 2)

ANALOG_VALUE:2140 Setpoint for 4 pipe regulation

°C / °F

Yes

DO_HEATING_HYST

(Note 3)

ANALOG_VALUE:2149 Heating hysteresis for on/off output

°C / °F

Yes

DO_COOLING_HYST

(Note 3)

ANALOG_VALUE:2150 Cooling hysteresis for on/off output

°C / °F

Yes

DIFF_2_STAGES

(Note 3)

ANALOG_VALUE:2151 Differential between 2 stages

°C / °F

Yes

DEAD_ZONE

(Note 3)

ANALOG_VALUE:2152 Neutral zone for 4 pipe systems

°C / °F

Yes

PROP_BAND_HEAT

(Note 3)

ANALOG_VALUE:2153 Heating proportional band

°C / °F

Yes

PROP_BAND_COOL

(Note 3)

ANALOG_VALUE:2154 Cooling proportional band

°C / °F

Yes

INTEGRAL_TIME

ANALOG_VALUE:2155 Integral time

s

Yes

SW_PT_FAN_1

ANALOG_VALUE:2156 Speed 1 activation point for 3 speed motor

%

Yes

SW_PT_FAN_2

ANALOG_VALUE:2157 Speed 2 activation point for 3 speed motor

%

Yes

SW_PT_FAN_3

ANALOG_VALUE:2158 Speed 3 activation point for 3 speed motor

%

Yes

«
...
115
116
117
118
119
...
»

Summary of Contents for TH-xxxSx1 Series































































































































Reviews:

No comments

Related manuals for TH-xxxSx1 Series

Brand: U-Prox Pages: 31

Brand: Acclaim Lighting Pages: 32

Brand: Jeep Pages: 19

Brand: Fanimation Pages: 2

Brand: M2M Pages: 24

Brand: Lattice Pages: 23

Brand: Lattice Semiconductor Pages: 2

Brand: Lathem Pages: 4

Brand: tams elektronik Pages: 36

Brand: KaRo Pages: 12

Tissue-Tek TEC 6

Brand: Sakura Seiki Pages: 6

Brand: fadini Pages: 28

Brand: GEA Pages: 47

Brand: Tech 21 Pages: 2

Brand: Quickie Pages: 64

Brand: Kamstrup Pages: 7

Expedition Double Jogger

Brand: BABYTREND Pages: 18

iEP-5000G Series

Brand: ASROCK Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands