IMG STAGE LINE ODP-1210RGBW Instruction Manual Download Page 14

Page: 14 / 38

7 Additional Functions

7.1 Key lock

A key lock may be activated as a protection
against unauthorized change of adjustments.
With activated lock, adjustments can only be
made after the input of a special key sequence.

1) Press the button MENU repeatedly until the

highest menu level is reached (in fig. 2 on the
very left).

2) Press the button UP or DOWN repeatedly

until the display shows

3) Press the button ENTER. The display shows

(key lock off).

4) Use the button UP or DOWN to switch to

As soon as the display is extinguished, the
key lock is activated.

5) To be able to make adjustments now:

a) When the display does not light up, first

press any button.

b) Press the button ENTER. The display will

be extinguished.

c) Then press the following buttons:

UP, DOWN, UP, DOWN.
Each time one of these buttons is
pressed, the display shows an asterisk ( ).

d) To finish press the button ENTER. The

display shows the last menu item
selected. As long as the display is illumi-
nated, adjustments can be made. When it
is extinguished, the key lock is reacti-
vated.

7.2 White balance

The spotlight is factory-set so that a certain white
shade is created at maximum brightness of the
colours red, green and blue. This white shade
may also be adjusted warmer or colder, e. g. to
balance differences to other spotlights when
these spotlights are controlled together with the
OPD-1210RGBW.

1) Press the button MENU repeatedly until the

highest menu level is reached (in fig. 2 on the
very left).

2) Press the button UP or DOWN repeatedly

until the display shows

3) Press the button ENTER. The display now

shows .

4) Press the button ENTER again. The display

now shows , or and a number between
000 and 255.

= brightness of red
= brightness of green
= brightness of blue

5) Select the three adjusting functions succes-

sively with the button ENTER and adjust the
brightness in each case with the button UP or
DOWN so that the desired shade of white
results.

6) Activate the adjusted shade of white:

a) Press the button MENU repeatedly until

the display shows

again.

b) Press the button DOWN twice so that the

display shows

c) Press the button ENTER. The display

shows

, ,

, or .

d) If

is not shown, press the button UP

or DOWN as many times as necessary.

e) Press the button ENTER. When the dis-

play shows

, the adjusted shade of

white is activated. When it shows

switch to

with the button UP or DOWN.

7) To be able to control the spotlight by DMX, go

from the menu branch

to the menu item

a) Press the button MENU repeatedly until

the display shows

again.

b) Press the button UP or DOWN repeatedly

until the display shows

c) Press the button ENTER. The display

shortly shows the DMX start address. If
DMX control signals are received now, a
point must flash on the display.

7.3 Slow response of the LEDs

LEDs respond immediately to a change of the
brightness adjustment. To simulate the slow
response of standard lamps, the response can
be adjusted in 4 steps. For the 11-channel mode

this adjustment is made via the DMX

channel 10 (chapter 6.3.5). For the 3-channel,
4-channel, 5-channel and 6-channel modes
make the adjustment as follows:

1) Press the button MENU repeatedly until the

highest menu level is reached (in fig. 2 on the
very left).

2) Press the button UP or DOWN repeatedly

until the display shows

3) Press the button ENTER. The display shows

, ,

, or .

4) If

is not shown, press the button UP or

DOWN as many times as necessary.

5) Press the button ENTER. The display shows

the present adjustment:

immediate response
slightly slow response

…

response as slow as possible

Select the desired adjustment with the button
UP or DOWN.

6) To be able to control the spotlight by DMX, go

from the menu branch

to the menu item

a) Press the button MENU repeatedly until

the display shows

again.

b) Press the button UP or DOWN repeatedly

until the display shows

c) Press the button ENTER. The display

shortly shows the DMX start address. If
DMX control signals are received now, a
point flashes on the display.

7.4 Resetting the spotlight

to the factory settings

The spotlight is factory-set as follows:

Function

Factory setting

colour spotlight

R = 255, G = 255,
B = 255, W = 030,
S = 00

show programs

AT.01

adjustment for the
master / slave mode

slave unit

DMX start address

001

number of DMX channels

= 11 channels

subaddress

function subaddress

off

function white balance

off

slow LED response

off

11 shades of white

factory-set values

white balance

R = 255, G = 255,
B = 255

key lock

off

To reset the spotlight to the factory settings:

1) Press the button MENU repeatedly until the

highest menu level is reached.

2) Press the button UP or DOWN repeatedly

until the display shows

3) Press the button ENTER. The display will

change

, ,

, or .

4) If

is not shown, press the button UP or

DOWN as many times as required.

5) Press the button ENTER. The display will be

extinguished. Then press the following but-
tons:
UP, DOWN, UP, DOWN.
Each time one of these buttons is pressed,
the display shows an asterisk ( ).
Press the button ENTER to start the reset.

6) Then switch back to

with the button

MENU. Select the operating mode with the
button UP or DOWN and activate it with the
button ENTER.

8 Specifications

Data protocol: . . . . . . . . . DMX 512

Number of
DMX channels: . . . . . . . . selectable:

3, 4, 5, 6 or 11

Light source : . . . . . . . . . 12 RGBW LEDs

Power per LED . . . . . . 8 W
Beam angle . . . . . . . . 25°

Power supply: . . . . . . . . . 230 V~ / 50 Hz

Power consumption: . . . . max. 120 VA

Protective class
of housing: . . . . . . . . . . . IP 67