Ikegami HC-HD300, Operation Manual

Page: 108 / 158

92 HC-HD300 1412 VER1 (U)
5.2 Settings from the Menu
Menu Item
Initial
Setting
Setting Value Description, Remarks
MENU DATA
ALL VF
―
INCOM MODE
NORMAL
NORMAL, CROSS,
1LINE ENG, USA,
USER1, USER2
Sets the connection (preset setting) of INCOM line. × ×
―
INCOM MODE SETUP
Sets the connection for when USER1/USER2 is selected in
INCOM MODE PRESET.
―
DATA LOAD
READY
READY, NORMAL,
CROSS, 1LINE ENG,
USA, USER1, USER2,
CANCEL
Load the setting that becomes a base of the setting. - -
―
INCOM1 MIX
ENG
ENG, PRD, BOTH,
SW LINK, OFF
Selects the line such that whether TALK line of INCOM1
is linked to ENG line, PROD line, both lines, or SW on the
back side, etc. *4
○ ×
―
INCOM2 MIX
PRD
ENG, PRD, BOTH,
SW LINK, OFF
Selects the line such that whether TALK line of INCOM2
is linked to ENG line, PROD line, both lines, or SW on the
back side, etc. *4
○ ×
― INCOM1 -> INCOM2
OFF ON, OFF Connects TALK line of INCOM1 to INCOM2.
○ ×
―
INCOM1 <- INCOM2
OFF ON, OFF Connects TALK line of INCOM2 to INCOM1. ○ ×
―
AFTER VR MIX
―
INCOM1 -> INCOM2
OFF ON, OFF Connects TALK line of INCOM1 to INCOM2. ○ ×
―
INCOM1 <- INCOM2
OFF ON, OFF Connects TALK line of INCOM2 to INCOM1. ○ ×
DATA SAVE
READY
READY, USER1, USER2,
CANCEL
Saves data as USER1 or USER2. - -
―
PGM FRONT VR
PGM1 PGM1, PGM2
Selects the signal to be controlled by PGM volume on the
right side of camera.
× ×
―
PGM SETUP
―
PGM LEVEL
LOW NORMAL, LOW Sets the output level of PGM. (Reduced by 10 dB with LOW) ○ ×
―
PGM2 OUT PGM2
ON ON, OFF Sets the ON/OFF for outputting PGM2 signal to PGM2. ○ ×
―
PGM2 OUT PGM3
OFF ON, OFF Sets the ON/OFF for outputting PGM3 signal to PGM2. ○ ×
―
PGM2 OUT MIC1
OFF ON, OFF Sets the ON/OFF for outputting MIC1 signal to PGM2. ○ ×
PGM2 OUT MIC2
OFF ON, OFF Sets the ON/OFF for outputting MIC2 signal to PGM2. ○ ×
BELT PACK(OPTION)
―
INCOM1 B.P
OFF ON, OFF Turns on when the belt pack is connected to INCOM1. × ×
INCOM2 B.P
OFF ON, OFF Turns on when the belt pack is connected to INCOM2. × ×
ENGINEER SET FILE RENEW - -
DATA RENEW MODE
Saves the conditions of camera level adjustment and menu.
The saved data can be loaded as user settings data of
"PRESET FILE LOAD" in MENU(3/4).
*4 : Selection switch on the rear panel of the MIC line typically controls only the TALK line, but SW LINK to be selected TALK line and LISTEN line both can be
controlled.