IHI IC75 Operation Manual Download Page 55 | Manualshive

Page: 55 / 106

IHI IC75 Operation Manual Download Page 55

OPERATION

IC75 ENG

3-13

PRECAUTION ON USE OF RUBBER CRAWLER SHOE

CAUTION

The rubber crawler shoe may be damaged or worn faster depending on working conditions.
Perform working operation properly according to working site conditions and machine
operation. Be sure to observe the prohibitions and instructions shown below.

Structure of Rubber Crawler Shoe

The structure of rubber crawler shoe. It consists of steel
cord to sustain tension, iron core to support it, and
covering rubber to them.

IMPORTANT

If a crack reaches the steel cord, it may be rusted
and cut off by moisture. When any crack is
detected, immediate repair is essential. Please
contact your local IHI distributor.

Cautions while working and traveling

Avoid the following while traveling.

DO NOT TRAVEL OR WORK ON STONE
FOUNDATIONS OR SHARP ROCKS

This wears down the lug and causes the steel cord to
break.

DO NOT TRAVEL OR WORK ON SURFACES WITH
MANY STONES SUCH AS RIVER BEDS

This causes damage or wear on the rubber crawler and
they may slip off.

Lug

Iron core

Steel cord

Covering rubber

«
...
53
54
55
56
57
...
»

Summary of Contents for IC75











































































































Reviews:

No comments