manualshive.com logo in svg

IFM Electronic LK31xx, Operating Instructions Manual, Page: 25 / 36

Share
Download
IFM Electronic LK31xx Operating Instructions Manual Download Page 25

25

UK

The unit can be configured before or after installation.  

Exception:  To adjust the overflow prevention [cOP], the unit must be 

installed in the tank. 

10.2  Basic settings 

Setting ranges of all parameters: 

→ 12

Factory settings of all parameters: 

→ 14

10.2.1  Set unit of measurement [uni]

 

►

Enter [uni] before entering the values SPx, rPx, OP or OFS. 

This avoids unintentional wrong settings.

 

►

Select [uni] 

 

►

Determine unit of measurement: [cm] or [inch]

uni

10.2.2  Set offset [OFS]

The distance between tank bottom and lower edge of the measuring probe can be 

entered as offset value 

(→ 5.6)

. 

 

►

Set [OFS] before the values for SP1, rP1 or OP are entered. 

This avoids unintentional wrong settings.

 

►

Select [OFS]. 

 

►

Set the value for the offset. Note the set unit of measurement [uni].

OFS

10.2.3  Set medium [MEdI]

 

►

Select [MEdI] 

 

►

Set sensitivity matching the medium to be detected: 

MEdI

[CLW.1] = water, hydrous media, coolant emulsions.
[CLW.2] = water, hydrous media, coolant emulsions for temperatures > 

35 °C (installation in climatic tube).

[OIL.1] = oils with an increased dielectric constant (e.g. some synthetic 

oils).

[OIL.2] = oils with a low dielectric constant (e.g. mineral oils).
[Auto] =

automatic medium detection.

 

►

In case of doubt, select [OIL.2] for oils. 

 

►

Check proper functioning in an application test.

Summary of Contents for LK31xx





































Reviews:

No comments