IES Keywatt 24 Wallbox User Manual Download

Page: 24 / 28

www.ies-synergy.com

User Manual

DUM016055-EN

Message

Description

Remote reset started... Station will reboot now.

Station is being rebooted.

Station rebooted. Please unplug your vehicle.

CCS only:

Station rebooted during a charge. Please

unplug and retry to launch the charge.

Warning: insulation failure.

Cable insulation failed. Please contact support.

Errors

The error messages are displayed with a characteristic screen. They are thus easily identifiable by the user. A

warning pictogram is displayed along with the error message as shown below.

The table below list errors messages who appears on the screen.

Error

Error resolution

Error occurred: 0x02 - 0X03 - 0X81

Emergency stop. Please unplug your vehicle and re-

lease the emergency button.

Not in CHAdeMO:

Emergency stop was initiated.

Please unplug your vehicle and release the emergen-

cy button.

Error occurred: 0x02 - 0X03 - 0X81

Emergency stop. Please unplug your vehicle and re-

lease the emergency button.

CHAdeMO only:

Emergency stop was initiated. Please

unplug your vehicle, press X and release the emer-

gency button.

Error occurred: 0x0A - 0x86

The charging station is overheating. Please unplug

your vehicle and check that no air vent is clogged.

Not in CHAdeMO:

The charging station is overheat-

ing. Please unplug your vehicle and check that no air

vent is clogged.

Error occurred: 0x0A - 0x86

The charging station is overheating. Check that no air

vent is clogged. Please press X once your vehicle is

unplugged.

CHAdeMO only:

The charging station is overheating.

Please unplug your vehicle, press X and check that no

air vent is clogged.

Error occurred: 0x51

The connection with the vehicle was lost. Please un-

plug your vehicle.

Not in CHAdeMO:

The connection with the vehicle

was lost. Please unplug your vehicle.

Error occurred: 0x07 - 0x29 - 0x51

The connection with the vehicle was lost. Please press

X once your vehicle is unplugged.

CHAdeMO only:

The connection with the vehicle was

lost. Please unplug then press X.

Error occurred: 0x22 - 0x33

Connector error. Please keep the connector closely

leant against your vehicle when plugging, until the

charge has started.

Not in CHAdeMO:

Connector error. Please keep the

connector closely leant against your vehicle when

plugging, until the charge has started.

Summary of Contents for Keywatt 24 Wallbox





























Search results

Summary of Contents for Keywatt 24 Wallbox

Reviews:

Related manuals for Keywatt 24 Wallbox

Brands by name

Popular brands

IES Keywatt 24 Wallbox, User Manual

Search results

Summary of Contents for Keywatt 24 Wallbox

Reviews:

Related manuals for Keywatt 24 Wallbox

Brands by name

Popular brands