IEI Technology NOVA-7820 Manual Download Page 35

Page: 35 / 47

Alarm Date

You can set time for date.

Alarm Hour

You can set time for hour.

Alarm Minute

You can set time for minute.

Alarm Second

You can set time for second.

Power Type Select

Select you use power type.

4.8 PCI / Plug and Play Setup Selections

AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP

Plug and Play Aware O/S No

Clear NVRAM on Every Boot No

On Board Audio Controller Enabled

On Board IEEEE1394 Controller Enabled

On Board PCMCIA Controller Enabled

PCI Latency Timer (PCI Clocks) 64

Primary Graphics Adapter External PCI

PCI VGA Palette Snoop er Disabled

Allocate IRQ to PCI VGA No

OffBoard PCI IDE Card Auto

OffBoard PCI IDE Primary IRQ Disabled

OffBoard PCI IDE Secondary IRQ Disabled

PCI Slot1 IRQ Priority Auto

PCI Slot2 IRQ Priority Auto

PCI Slot3 IRQ Priority Auto

PCI Slot4 IRQ Priority Auto

DMA Channel 0 PnP

DMA Channel 1 PnP

DMA Channel 3 PnP

DMA Channel 5 PnP

DMA Channel 6 PnP

DMA Channel 7 PnP

IRQ3 PCI/PnP

IRQ4 PCI/PnP

IRQ5 PCI/PnP

IRQ7 PCI/PnP

IRQ9 PCI/PnP

IRQ10 PCI/PnP

IRQ11 PCI/PnP

IRQ14 PCI/PnP

IRQ15 PCI/PnP

Available Options:

> Yes

ESC: Exit

↑↓

: Sel

PgUp/PgDn: Modify

F1: Help F2/F3: Color

Figure 6: PCI / Plug and Play Setup

Plug and Play Aware O/S

If enable, BIOS will configure only PnP ISA boot devices (i.e. all PnP ISA

cards which has boot flag set). And PnP aware OS will configure all other

Summary of Contents for NOVA-7820















































Search results

Summary of Contents for NOVA-7820

Reviews:

IEI Technology NOVA-7820, Manual, Page: 35 / 47

Search results

Summary of Contents for NOVA-7820

Reviews: