manualshive.com logo in svg

IEI Technology NOVA-7820, Manual, Page: 20 / 47

Share
Download
IEI Technology NOVA-7820 Manual Download Page 20

 20

 

3.15 External Switches and Indicators 

 

There are several external switches and indicators for monitoring and 

controlling your CPU board.  All the functions are in the CN7, CN12, and 

CN20 connectors. 

 

• 

Suspend Led Connector (CN7) 

 

PIN Description 

1 LED+ 
2 LED- 

 

• 

ATX Power On/Off Button Connector (CN12) 

 

PIN Description 

1 PWR 
2 GROUND 

 

• 

CN20: Multi Panel 

 

PIN Description PIN  Description 

1 

POWER-LED + 

2 

SPEAKER - 

3 N/C 

4 N/C 

5 POWER-LED 

- 

6 N/C 

7  

8 SPEAKER 

+5V 

9 KEYLOCK- 

10 RESET 

SW 

11  GROUND 

12  RESET SW GND 

13  HDD LED+ 

14  HDD LED - 

 

 

3.16 IEEE-1394 Connector 

 

NOVA-7820 is equipped witch IEEE1394 controller (TI TSB43AA22).  You 

can connect it to your 1394 device through CN21, 36 connectors.  The pin 

assignments are as follows: 

 

• 

CN21: 1394 Connector 

 

PIN Description PIN Description 

1 VCC12V 2 GROUND 
3 TPB- 4 TPB+ 
5 TPA- 6 TPA+ 
7 NC/FG 8 NC/FG 

 

• 

CN36: 1394 Connector 

 

PIN Description PIN Description 

1 VCC12V 2 GROUND 
3 TPB- 4 TPB+ 
5 TPA- 6 TPA+ 

 

Summary of Contents for NOVA-7820
















































Reviews:

No comments