manualshive.com logo in svg

IEI Technology NOVA-7820, Manual, Page: 18 / 47

Share
Download
IEI Technology NOVA-7820 Manual Download Page 18

 18

 

3.11 Audio Connectors 

 

NOVA-7820 has a built-in AUDIO chipset (CMEDIA CMI8738LX); connector 

directly connects to the pin-header (CN32).  The audio chipset can support 

5.1 channel sounds that include LINE-OUT, REAR, and CENTER/BASS. 

 

• 

CN32: Audio Connector (2x8_2.00mm) 

 

PIN Description  PIN  Description 

1 LINEOUT_L  2  GROUND 
3 LINEOUT_R  4  GROUND 
5 CENTER  6  BASS 
7 GROUND 8 GROUND 
9 LININ_L 10 LINEIN_R 

11 GROUND 12 GROUND 
13 REAR_L  14  REAR_R 
15 MIN_IN  16 GROUND 

 

• 

CDIN1: CD-IN 

 

PIN Description 

1 

CD LEFT SIGNAL 

2 GROUND 
3 GROUND 
4 

CD RIGHT SIGNAL 

 
 

3.12 VGA Connector  

 

NOVA-7820 has a built-in 15-pin VGA connector directly to your CRT 

monitor. 

 

• 

CON1: 15-pin Female Connector 

 

PIN Description PIN Description 

1 RED 

2 GREEN 

3 BLUE 

4 N/C 

5 GROUND 

6 GROUND 

7 GROUND 

8 GROUND 

9 VCC 

10 GROUND 

11 N/C 

12 DDC 

DAT 

13 HSYNC 

14 VSYNC 

15 DDCCLK 

 

 

 

Summary of Contents for NOVA-7820
















































Reviews:

No comments