manualshive.com logo in svg

IEI Technology NOVA-7820, Manual, Page: 16 / 47

Share
Download
IEI Technology NOVA-7820 Manual Download Page 16

 16

 

• 

CN48: 10-pin Connector 

 

PIN Description 

1 

DATA CARRIER DETECT (DCD) 

2 

RECEIVE DATA (RXD) 

3 

TRANSMIT DATA (TXD) 

4 

DATA TERMINAL READY (DTR) 

5 GROUND 
6 

DATA SET READY (DSR) 

7 

REQUEST TO SEND (RTS) 

8 

CLEAR TO SEND (CTS) 

9 

RING INDICATOR (RI) 

10 N/C 

 

• 

CN49: 14-pin Connector 

 

PIN Description 

1 

DATA CARRIER DETECT (DCD) 

2 

RECEIVE DATA (RXD) 

3 

TRANSMIT DATA (TXD) 

4 

DATA TERMINAL READY (DTR) 

5 GROUND 
6 

DATA SET READY (DSR) 

7 

REQUEST TO SEND (RTS) 

8 

CLEAR TO SEND (CTS) 

9 

RING INDICATOR (RI) 

10 N/C 
11 TX+ 

(RS422/485) 

12 TX- 

(RS422/485) 

13 RX+ 

(RS422/485) 

14 

RX-  (RS422/485) 

 

 

3.7 Power 

Connector 

 

NOVA-7820 has one power connector for power supply. 

 

• 

CN30: Power Supply Connector 

 

PIN Description 

1 VCC12V 
2 

GROUND

 

3 

GROUND

 

4 VCC5V 

 

• 

CN26: ATX Power Connector 

 

PIN Description 

1 VCC5VSB 
2 PS_ON 
3 GROUND 

 

Summary of Contents for NOVA-7820
















































Reviews:

No comments