manualshive.com logo in svg

IEI Technology NOVA-7820, Manual, Page: 13 / 47

Share
Download
IEI Technology NOVA-7820 Manual Download Page 13

 13

 

3.1  Floppy Disk Drive Connector 

 

NOVA-7820 board is equipped with a 34-pin daisy-chain driver connector 

cable. 

 

• 

CN24: FDD Connector 

 

PIN Description  PIN Description 

1 GROUND 

2 REDUCE 

WRITE 

3 GROUND 

4 N/C 

5 GROUND 

6 DS1# 

7 GROUND 

8 INDEX# 

9 

GROUND 

10 

MOTOR ENABLE A# 

11 GROUND 

12 DRIVE 

SELECT 

B# 

13 GROUND 

14 DRIVE 

SELECT 

A# 

15 GROUND 

16 MOTOR 

ENABLE 

B# 

17 GROUND 

18 DIRECTION# 

19 GROUND 

20 STEP# 

21 GROUND 

22 WRITE 

DATA# 

23 GROUND 

24 WRITE 

GATE# 

25 GROUND 

26 TRACK 

0# 

27 GROUND 

28 WRITE 

PROTECT# 

29 N/C 

30 READ 

DATA# 

31 GROUND 

32 SIDE 

1 

SELECT# 

33 N/C 

34 DISK 

CHANGE# 

 
 

3.2 Video-in 

Connector 

 

NOVA-7820 is equipped witch 4 channels of composite video 

connector(BT878A). 

 

• 

CN33: Capture IN 

 

PIN Description  PIN  Description 

1 AVIN0  2 GROUND 
3 AVIN1  4 GROUND 
5 AVIN2  6 GROUND 
7 AVIN3  8 GROUND 

 

Summary of Contents for NOVA-7820
















































Reviews:

No comments