IEI Technology NANO-LX User Manual Download Page 85

Page: 85 / 213

NANO-LX CPU Card

3.4.6 SERIRQ Select Jumper

NOTE:

Serial IRQ can only work properly if PCMCIA supports Serial IRQ signal.

Jumper Label:

JP6

Jumper Type:

2-pin header

Jumper Settings:

See Table 3-41

Jumper Location:

See Figure 3-33

Use the JP6 jumper to reserve IRQ addresses for PCMCIA devices.

JP6

Description

Short SERIRQ

Enable

Open SERIRQ

Disable

Table 3-41: JP6 Jumper Settings

3.4.7 LCD Panel (LVDS/TTL) Voltage select Jumper

Jumper Label:

JP7

Jumper Type:

3-pin header

Jumper Settings:

See Table 3-42

Jumper Location:

See Figure 3-33

The JP7 jumper sets the voltage to the LCD panel.

JP7

Description

1-2

Panel Voltage select 3.3V (Default)

2-3

Panel Voltage select 5V

Table 3-42: JP7 Jumper Settings

Summary of Contents for NANO-LX






















































































































































































































Search results

Summary of Contents for NANO-LX

Reviews:

Brands by name

Popular brands

IEI Technology NANO-LX, User Manual

Search results

Summary of Contents for NANO-LX

Reviews:

Brands by name

Popular brands