IEI Technology NANO-LX User Manual Download Page 124

Page: 124 / 213

124

IEI

Technology, Corp

x RxD, TxD Active [Hi,Lo]

The

RxD, TxD Active

option can only be selected if the

UART Mode Select

option is set to

IrDA mode or ASKIR mode. Use the

RxD, TxD Active

option to set the infrared reception

(RxD) and transmission (TxD) polarity. The

RxD, TxD Active

options are:

Hi, Hi

Hi, Lo (Default)

Lo, Hi

Lo, Lo

x IR Transmission Delay [Enabled]

Use the

IR Transmission Delay

option to enable or disable IR transmission delays.

Disabled

IR transmission are not delayed.

Enabled

(Default)

IR transmission are delayed.

x UR2 Duplex Mode [Half]

Use the

UR2 Duplex Mode

option to specify the transmission mode for the IR port device.

Full

Simultaneous

bi-directional transmission occurs.

Half

(Default)

Transmission only occurs in one direction at a time.

x Use IR Pins [IR-Rx2Tx2]

Use the

Use IR Pins

options to specify how the IR pins respond. The

Use IR Pins

options

are:

RxD2,TxD2

IR-Rx2Tx2 (Default)

Summary of Contents for NANO-LX






















































































































































































































Search results

Summary of Contents for NANO-LX

Reviews:

Brands by name

Popular brands

IEI Technology NANO-LX, User Manual

Search results

Summary of Contents for NANO-LX

Reviews:

Brands by name

Popular brands