IEI Technology KINO-KX Series User Manual Download Page 90

Page: 90 / 110

KINO-KX SBC

Page 78

5.4.3.2 IOE SATA Drive Setup

Use the

IOE SATA Drive Setup

menu (

BIOS Menu 24

) to configure Serial ATA.

Chipset

CND003 SATA Controller

[Enabled]

Configure SATA as

[AHCI]

Force SATA Speed setting

[Gen3]

AHCI Port HotPlug Cap

[Disabled]

Serial ATA Port 0

Empty

Serial ATA Port 1

Empty

Serial ATA Port 2

Empty

Serial ATA Port 3

Empty

Select whether to enable
or disable SATA
controller.

---------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change  Opt.
F1:  General Help
F2:  Previous Values
F3:

Optimized

Defaults
F4:

Save & Exit

ESC: Exit

BIOS Menu 24: IOE SATA Drive Setup



CND003 SATA Controller [Enabled]

Use the

CND003 SATA Controller

option to enable or disable the on-chip SATA

controller.



Disabled

Disables the SATA controller.



Enabled

EFAULT

Enables the SATA controller.



Configure SATA as [AHCI]

Use the

Configure SATA as

option to configure SATA devices as IDE or AHCI devices.



IDE

Configures SATA devices as IDE device.



AHCI

EFAULT

Configures SATA devices as AHCI device.

Summary of Contents for KINO-KX Series















































































































Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands

IEI Technology KINO-KX Series, User Manual

Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands