IEI Technology KINO-KX Series User Manual Download Page 81

Page: 81 / 110

KINO-KX SBC

Page 69

5.3.9 USB Configuration

Use the

USB Configuration

menu (

BIOS Menu 15

) to read USB configuration

information and configure the USB settings.

Advanced

USB Configuration

USB Devices:
1 Keyboard

Legacy USB Support

[Enabled]

Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.

---------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1: General Help
F2: Previous Values
F3:

Optimized

Defaults
F4:

Save & Exit

ESC: Exit

BIOS Menu 15: USB Configuration



Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB

keyboard can control the system even when there is no USB driver loaded onto the

system.



Enabled

EFAULT

Legacy USB support enabled



Disabled

Legacy USB support disabled



Auto

Legacy USB support disabled if no USB devices are

connected

Summary of Contents for KINO-KX Series















































































































Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands

IEI Technology KINO-KX Series, User Manual

Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands