IEI Technology KINO-KX Series User Manual Download Page 14

Page: 14 / 110

KINO-KX SBC

Page 2

1.1 Introduction

Figure 1-1: KINO-KX

The KINO-KX series is a Mini-ITX form factor single bard computer. It has an on-board

Zhaoxin KX-U6780A/KX-U6580 processor, and supports two 260-pin 2666 MHz

dual-channel DDR4 SO-DIMM slots with up to 64.0 GB of memory.

The KINO-KX provides two GbE interfaces through the Realtek RTL8111H controllers.

The integrated Zhaoxin ZX-200 chipset supports four SATA 6Gb/s drives and one full-size

PCIe Mini slot. In addition, the KINO-KX includes VGA and DVI-I interfaces for dual

independent display.

Expansion and I/O include one PCIe x16 slot, four USB 3.2 Gen 1 (5Gb/s) on the rear

panel, ten USB 2.0 on the rear panel and ten RS-232. High Definition Audio (HDA)

support ensures HDA devices can be easily implemented on the KINO-KX.

Summary of Contents for KINO-KX Series















































































































Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands

IEI Technology KINO-KX Series, User Manual

Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands