IEI Technology KINO-KX Series User Manual Download Page 67

Page: 67 / 110

KINO-KX SBC

Page 55

5.3 Advanced

Use the

Advanced

menu (

BIOS Menu 2

) to configure the CPU and peripheral devices

through the following sub-menus:

WARNING!

Setting the wrong values in the sections below may cause the system

to malfunction. Make sure that the settings made are compatible with

the hardware.

Main

Advanced

Chipset

Security

Boot

Save & Exit

> Trusted Computing
> ACPI Settings
> RTC Wake Settings
> F81866 Super IO Configuration
> Hardware Monitor
> F81216SEC Super IO Configuration
> Serial Port Console Redirection
> CPU Configuration
> USB Configuration

Trusted Computing
Settings

----------------------



: Select Screen

↑

↓

: Select Item

Enter

Select

+/-: Change Opt.
F1:  General Help
F2:  Previous Values
F3:  Optimized Defaults
F4:  Save & Exit
ESC: Exit

BIOS Menu 2: Advanced

Summary of Contents for KINO-KX Series















































































































Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands

IEI Technology KINO-KX Series, User Manual

Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands