IEI Technology KINO-KX Series User Manual Download Page 86

Page: 86 / 110

KINO-KX SBC

Page 74



Reset PCIE When Link Fail [Disabled]

Use the

Reset PCIE When Link Fail

option to configure whether to reset PCI Express

device when link fail.



Disabled

EFAULT

Do not reset PCI Express device when link fail.



Enabled

Reset PCI Express device when link fail.



PCIEX16 Slot Capability Control [Auto]

Use the

PCIEX16 Slot Capability Control

option to select the maximum link speed of the

PCI Express x16 slot. The following options are available:



Auto

Default



Force Gen 1



Force Gen 2



Force Gen 3



PCIEX16 Slot [Enabled]

Use the

PCIEX16 Slot

option to enable or disable the PCIe x16 slot.



Disabled

Disables the PCIe x16 slot.



Enabled

EFAULT

Enables the PCIe x16 slot.



SSC Manual Control [Disabled]

Use the

SSC Manual Control

option to enable or disable SSC manual control. The

system must be reboot after changing this setting.



Disabled

EFAULT

Disables SSC manual control.



Enabled

Enables SSC manual control.

Summary of Contents for KINO-KX Series















































































































Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands

IEI Technology KINO-KX Series, User Manual

Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands