IEI Technology KINO-KX Series User Manual Download Page 59

Page: 59 / 110

KINO-KX SBC

Page 47

4.6 Chassis Installation

4.6.1 Airflow

WARNING:

Airflow is critical for keeping components within recommended

operating temperatures. The chassis should have fans and vents as

necessary to keep things cool.

The KINO-KX must be installed in a chassis with ventilation holes on the sides allowing

airflow to travel through the heat sink surface. In a system with an individual power supply

unit, the cooling fan of a power supply can also help generate airflow through the board

surface.

4.6.2 Motherboard Installation

To install the KINO-KX motherboard into the chassis please refer to the reference material

that came with the chassis.

4.7 SATA Drive Connection

The KINO-KX is shipped with a SATA drive cable. To connect the SATA drive to the

connector, please follow the steps below.

Step 1:

Locate the SATA connector and the SATA power connector

. The locations of

the connectors are shown in

Chapter 3

Step 2:

Insert the cable connector

. Insert the cable connector into the on-board SATA

drive connector until it clips into place. See

Figure 4-7

Summary of Contents for KINO-KX Series















































































































Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands

IEI Technology KINO-KX Series, User Manual

Search results

Summary of Contents for KINO-KX Series

Reviews:

Related manuals for KINO-KX Series

Brands by name

Popular brands