IEI Technology IMBA-XQ354S User Manual Download Page 92

Page: 92 / 181

IMBA-XQ354S Motherboard

Page 76

Figure 4-21: VGA Connector

Step 4:

Secure the connector

. Secure the D-sub 15 VGA connector from the VGA

monitor to the external interface by tightening the two retention screws on either

side of the connector.

Step 0:

4.6.7 Audio Connector

The six audio jacks on the external audio connector enable the IMBA-XQ354S to be

connected to a 7.1 channel surround sound setup. To install the audio devices, follow the

steps below.

Step 1:

Identify the audio plugs

. The plugs on your home theater system or speakers

may not match the colors on the rear panel. If audio plugs are plugged into the

wrong jacks, sound quality will be very bad.

Step 2:

Plug the audio plugs into the audio jacks

. Plug the audio plugs into the audio

jacks. If the plugs on your speakers are different, an adapter will need to be used

to plug them into the audio jacks.

CEN/LFE Out (Orange)

: Connects to the center speaker and sub-woofer.

Surround Out (Black)

: Connects to a speaker on the left and right.

Summary of Contents for IMBA-XQ354S






















































































































































































Search results

Summary of Contents for IMBA-XQ354S

Reviews:

Brands by name

Popular brands

IEI Technology IMBA-XQ354S, User Manual

Search results

Summary of Contents for IMBA-XQ354S

Reviews:

Brands by name

Popular brands