IEI Technology IMBA-XQ354S User Manual Download Page 68

Page: 68 / 181

IMBA-XQ354S Motherboard

Page 52

Before and during the installation of the IMBA-XQ354S

DO NOT:

Remove any of the stickers on the PCB board. These stickers are required for

warranty validation.

Use the product before verifying all the cables and power connectors are

properly connected.

Allow screws to come in contact with the PCB circuit, connector pins, or its

components.

4.2.2 Installation Checklist

The following checklist is provided to ensure the IMBA-XQ354S is properly installed.

All the items in the packing list are present

A compatible memory module is properly inserted into the slot

The jumpers have been properly configured

The IMBA-XQ354S is inserted into a chassis with adequate ventilation

The correct power supply is being used

The following devices are properly connected

RS-232 cables

USB cables

FDD cables

Power cables

The following external peripheral devices are properly connected to the

chassis:

VGA screen

Keyboard

Mouse

RS-232 serial communications device

Summary of Contents for IMBA-XQ354S






















































































































































































Search results

Summary of Contents for IMBA-XQ354S

Reviews:

Brands by name

Popular brands

IEI Technology IMBA-XQ354S, User Manual

Search results

Summary of Contents for IMBA-XQ354S

Reviews:

Brands by name

Popular brands