manualshive.com logo in svg

IEI Technology eKINO-945GSE, User Manual, Page: 93 / 215

Share
Download
IEI Technology eKINO-945GSE User Manual Download Page 93

 

 

eKINO-945GSE Motherboard 

Page 77 

 

Figure 5-5: IDE Cable Connection 

Step 6: 

Connect the cable to an IDE device

. Connect the two connectors on the other 

side of the cable to one or two IDE devices. Make sure that pin 1 on the cable 

corresponds to pin 1 on the connector.

 

Step 0:

 

5.9.2 SATA Drive Connection 

The eKINO-945GSE is shipped with two SATA drive cables and one SATA drive power 

cable. To connect the SATA drives to the connectors, please follow the steps below. 

Step 1: 

Locate the connectors

. The locations of the SATA drive connectors are shown 

in 

Chapter 3

. 

Step 2: 

Insert the cable connector

. Press the clip on the connector at the end of the 

SATA cable and insert the cable connector into the onboard SATA drive 

connector. See 

9

Figure 5-6

. 

Summary of Contents for eKINO-945GSE
























































































































































































































Reviews:

No comments