IEI Technology eKINO-945GSE User Manual Download Page 66

Page: 66 / 215

eKINO-945GSE Motherboard

Page 50

The 10-pin serial port connectors provide RS-232 serial communications channels. The

COM serial port connectors can be connected to external RS-232 serial port devices.

COM3 uses JP2 for RS-422 and RS-485 connectivity.

Figure 4-18: RS-232 Connector Pinout Locations

Pin

No. Description

Pin

No. Description

Data Carrier Direct (DCD)

Data Set Ready (DSR)

Receive Data (RXD)

Request To Send (RTS)

Transmit Data (TXD)

Clear To Send (CTS)

Data Terminal Ready (DTR)

Ring Indicator (RI)

9 Ground

(GND)

N/C

Table 4-15: RS-232 Connector Pinouts

4.2.18 Serial Port Connectors (RS-422/485)

CN Label:

JP2

CN Type:

6-pin header (2x3)

CN Location:

See

Figure 4-19

Summary of Contents for eKINO-945GSE
























































































































































































































Search results

Summary of Contents for eKINO-945GSE

Reviews:

IEI Technology eKINO-945GSE, User Manual, Page: 66 / 215

Search results

Summary of Contents for eKINO-945GSE

Reviews: