IEI Technology eKINO-945GSE User Manual Download Page 21

Page: 21 / 215

eKINO-945GSE Motherboard

Page 5

1.2.3 Technical Specifications

eKINO-945GSE technical specifications are listed in

Specification

eKINO-945GSE

Form Factor

Mini-ITX

System CPU

45 nm 1.60 GHz Intel® Atom™ N270

Front Side Bus (FSB)

533 MHz

System Chipset

Northbridge: Intel® 945GSE

Southbridge: Intel® ICH7M

Memory

One 200-pin SO-DIMM socket supports one 533 MHz 2.0 GB

(max.) DDR2 SDRAM SO-DIMM

CompactFlash®

One CompactFlash® socket

Super I/O

iTE IT8718F

Display

VGA

DVI (through Silicon Image Sil1362 on SDVO)

LVDS

HDTV

BIOS

AMI BIOS label

Audio

Realtek ALC655 AC'97 codec

LAN

Two Realtek RTL8111C PCIe GbE controllers

COM

Three RS-232 serial ports (one internal, two external)

One RS-232/422/485 serial port (internal)

USB2.0

Six USB 2.0 devices supported (two internal, four external)

Hard Drives

One 44-pin IDE connector

SATA

Two 1.5 Gb/s SATA drives supported

Keyboard/mouse

Internal pin header.

Digital I/O

One 8-bit digital input/output connector; 4-bit input/4-bit output

through the iTE IT8718F super I/O

Summary of Contents for eKINO-945GSE
























































































































































































































Search results

Summary of Contents for eKINO-945GSE

Reviews:

IEI Technology eKINO-945GSE, User Manual, Page: 21 / 215

Search results

Summary of Contents for eKINO-945GSE

Reviews: