IEI Technology eKINO-945GSE User Manual Download Page 150

Page: 150 / 215

eKINO-945GSE Motherboard

Page 134

Combo Mode

A fixed portion of graphics memory is reserved as

graphics memory. If more memory is needed,

graphics memory is dynamically allocated

according to the system and graphics needs.

DVMT/FIXED Memory [128 MB]

Use the

DVMT/FIXED Memory

option to specify the maximum amount of memory that

can be allocated as graphics memory. This option can only be configured for if

DVMT

Mode

Fixed Mode

is selected in the

DVMT Mode Selec

t option. If

Combo Mode

selected, the maximum amount of graphics memory is 128 MB. Configuration options are

listed below.

128

EFAULT

Maximum

DVMT

Boot Display Device [Auto]

The

Boot Display Device

BIOS option selects the display device the system uses when it

boots. The available options are listed below:

Auto

EFAULT

CRT

EFP

LFP

LVDS1 Panel Type [by H/W]

Use the

LVDS Panel Type

to determine the LCD panel resolution. Configuration options

are listed below:

640 x 480 18-bit

800 x 480 18-bit

800 x 600 18-bit

1024 x 768 18-bit

Default

Summary of Contents for eKINO-945GSE
























































































































































































































Search results

Summary of Contents for eKINO-945GSE

Reviews:

IEI Technology eKINO-945GSE, User Manual, Page: 150 / 215

Search results

Summary of Contents for eKINO-945GSE

Reviews: