IEI Technology eKINO-945GSE User Manual Download Page 79

Page: 79 / 215

eKINO-945GSE Motherboard

Page 63

5.2 Installation Considerations

NOTE:

The following installation notices and installation considerations should

be read and understood before the eKINO-945GSE is installed. All

installation notices pertaining to the installation of the eKINO-945GSE

should be strictly adhered to. Failing to adhere to these precautions

may lead to severe damage of the eKINO-945GSE and injury to the

person installing the motherboard.

5.2.1 Installation Notices

WARNING:

The installation instructions described in this manual should be

carefully followed in order to prevent damage to the eKINO-945GSE,

eKINO-945GSE components and injury to the user.

Before and during the installation please

the following:

Read the user manual:

The user manual provides a complete description of the eKINO-945GSE

installation instructions and configuration options.

Wear an electrostatic discharge cuff (ESD):

Electronic components are easily damaged by ESD. Wearing an ESD cuff

removes ESD from the body and helps prevent ESD damage.

Place the eKINO-945GSE on an antistatic pad:

When installing or configuring the motherboard, place it on an antistatic

pad. This helps to prevent potential ESD damage.

Turn all power to the eKINO-945GSE off:

When working with the eKINO-945GSE, make sure that it is disconnected

from all power supplies and that no electricity is being fed into the system.

Summary of Contents for eKINO-945GSE
























































































































































































































Search results

Summary of Contents for eKINO-945GSE

Reviews:

IEI Technology eKINO-945GSE, User Manual, Page: 79 / 215

Search results

Summary of Contents for eKINO-945GSE

Reviews: