IEI Technology eKINO-945GSE User Manual Download Page 120

Page: 120 / 215

eKINO-945GSE Motherboard

Page 104

Normal

Default

IrDA

ASK

Serial Port2 Address [2F8/IRQ3]

Use the

Serial Port2 Address

option to select the I/O and IRQ addresses.

Disabled

No base address is assigned to Serial Port 2

2F8/IRQ3 D

EFAULT

I/O port address is 3F8 and the interrupt address is IRQ3

3E8/IRQ4

I/O port address is 3E8 and the interrupt address is IRQ4

2E8/IRQ3

I/O port address is 2E8 and the interrupt address is IRQ3

Serial Port2 Mode [Normal]

Use the

Serial Port2 Mode

option to select the transmitting and receiving mode.

Normal

Default

IrDA

ASK

Serial Port3 Address [3E8]

Use the

Serial Port 3 Address

option to set the I/O address.

Disabled

No I/O address assigned

3E8 D

EFAULT

The assigned I/O address is 3E8

2E8

The assigned I/O address is 2E8

2F0

The assigned I/O address is 2F0

2E0

The assigned I/O address is 2E0

Serial Port 3 IRQ [11]

Use the

Serial Port 3 IRQ

option selects the IRQ.

Default

Summary of Contents for eKINO-945GSE
























































































































































































































Search results

Summary of Contents for eKINO-945GSE

Reviews:

IEI Technology eKINO-945GSE, User Manual, Page: 120 / 215

Search results

Summary of Contents for eKINO-945GSE

Reviews: