IEI Technology eKINO-945GSE User Manual Download Page 188

Page: 188 / 215

eKINO-945GSE Motherboard

Page 172

Below is a list of BIOS configuration options in the BIOS chapter.

System Overview .................................................................................................................92

System Time [xx:xx:xx] .......................................................................................................93

System Date [xx/xx/xx] ........................................................................................................93

ATA/IDE Configurations [Compatible]...............................................................................96

Legacy IDE Channels [PATA Pri, SATA Sec] ....................................................................97

IDE Master and IDE Slave....................................................................................................97

Auto-Detected Drive Parameters........................................................................................98

Type [Auto] ...........................................................................................................................99

LBA/Large Mode [Auto].................................................................................................... 100

Block (Multi Sector Transfer) [Auto] ............................................................................... 100

PIO Mode [Auto]................................................................................................................ 100

DMA Mode [Auto].............................................................................................................. 101

S.M.A.R.T [Auto]................................................................................................................ 102

32Bit Data Transfer [Enabled].......................................................................................... 102

Serial Port1 Address [3F8/IRQ4] ..................................................................................... 103

Serial Port1 Mode [Normal].............................................................................................. 103

Serial Port2 Address [2F8/IRQ3] ..................................................................................... 104

Serial Port2 Mode [Normal].............................................................................................. 104

Serial Port3 Address [3E8]............................................................................................... 104

Serial Port 3 IRQ [11] ........................................................................................................ 104

Select RS232 or RS422/RS485 [RS232] .......................................................................... 105

Serial Port4 Address [2E8]............................................................................................... 105

Serial Port 4 IRQ [10] ........................................................................................................ 105

Serial Port6 Address [2E0]............................................................................................... 105

Serial Port 6 IRQ [11] ........................................................................................................ 106

CPU FAN Mode Setting [Full On Mode] .......................................................................... 106

CPU Temp. Limit of OFF [000] ......................................................................................... 107

CPU Temp. Limit of Start [020] ........................................................................................ 108

CPU Fan Start PWM [070]................................................................................................. 108

Slope PWM [0.5 PWM].................................................................................................... 108

Suspend Mode [S1(POS)]................................................................................................. 111

Power Button Mode [On/Off]............................................................................................ 112

Resume on Keyboard/Mouse [Disabled] ........................................................................ 113

Summary of Contents for eKINO-945GSE
























































































































































































































Search results

Summary of Contents for eKINO-945GSE

Reviews:

IEI Technology eKINO-945GSE, User Manual, Page: 188 / 215

Search results

Summary of Contents for eKINO-945GSE

Reviews: