IDT Digital Encoder Plus User Manual Download Page 12

Page: 12 / 98

INSTALLATION

Dedicate one hour to the installation.

WARNING

IDT declines all liability should the rules of installation below not be

respected.

Physical Installation

As you will have noticed all IDT products are of a 19 inch format so that it fits

into dedicated racks. The following indications must be respected.

We advise using a rack-mount; however, the front panel was designed to be

sturdy enough to be self-supporting with the four screws firmly implanted.

The ventilation of your processor:

the ventilation has been studied to make

sure that all heat generated is evacuated. Air is sucked in by two ventilators,

placed on the right and is expired at the rear and to the left of the unit.
These ducts should absolutely not be obstructed. Make sure that your processor

is placed where hot air can be evacuated. The ideal location is in an open rack,

dry area where, ideally, it is not exposed to high temperatures (behind a window
with bright sunshine, a radiator, amplifier etc).

IDT processors have been tested to work in environments where the

temperatures go from 0°C

to 45°C. IDT Sound Processing Corporation cannot

guarantee that its processors work perfectly outside these temperatures.

Summary of Contents for Digital Encoder Plus



































































































Search results

Summary of Contents for Digital Encoder Plus

Reviews:

Related manuals for Digital Encoder Plus

Brands by name

Popular brands

IDT Digital Encoder Plus, User Manual

Search results

Summary of Contents for Digital Encoder Plus

Reviews:

Related manuals for Digital Encoder Plus

Brands by name

Popular brands