IDK MSD-701UHD Command Reference Manual Download

Page: 18 / 115

MSD-701UHD / 702UHD / 801UHD/ 802UHD Command Guide

3.3.2 Input channels

@GSW / @SSW

Switching video and audio channel simultaneously

Getting

Command

@GSW

Response

@GSW, video_1, audio_1, video_2, audio_2,

Setting

Command

@SSW, input_1, output_1 (, input_2, output_2)

Response

@SSW, input_1, output_1 (, input_2, output_2)

Parameter

video_1-2: Video input channel

audio_1-2: Audio input channel

input_1-2 : Video and audio input channel

0 = OFF [Default], 1 = IN1 to 8 = IN8

output_1-4: Video and audio output channel

0 = All outputs, 1 = OUT1, 2= OUT2

Getting

example

Command

Response

@GSW

@GSW,2,2,0,0,

Description Getting the video and audio input channels that are assigned to output channels.

OUT1: IN2, OUT2: OFF

Setting

example

Command

Response

@SSW,1,1

Description Setting IN1 video and audio to be output to OUT1.

Remarks

－

Summary of Contents for MSD-701UHD




















































































































Search results

Summary of Contents for MSD-701UHD

Reviews:

Related manuals for MSD-701UHD

Brands by name

Popular brands

IDK MSD-701UHD, Command Reference Manual

Search results

Summary of Contents for MSD-701UHD

Reviews:

Related manuals for MSD-701UHD

Brands by name

Popular brands