IDK MSD-701UHD Command Reference Manual Download

Page: 109 / 115

MSD-701UHD / 702UHD / 801UHD/ 802UHD Command Guide

109

@GBZ / @SBZ

Buzzer

Getting

Command

@GBZ

Response

@GBZ, bz

Setting

Command

@SBZ, bz

Response

@SBZ, bz

Parameter

bz: Buzzer sound

0 = OFF, 1 = ON [Default]

Getting

example

Command

Response

@GBZ

@GBZ,1

Description Getting the buzzer status.

Setting

example

Command

Response

@SBZ,1

Description Enabling buzzer.

Remarks

－

@GHP / @SHP

Power supply of HDBaseT input

Getting

Command

@GHP

Response

@GHP, mode

Setting

Command

@SHP, mode

Response

@SHP, mode

Parameter

mode: Power supply

0 = OFF [Default], 1 = ON

Getting

example

Command

Response

@GHP

@GHP,0

Description Getting the power supply setting of HDBaseT input.

Power supply of HDBaseT input is set to OFF.

Setting

example

Command

Response

@SHP,1

Description Power supply of HDBaseT input is set to ON.

Remarks

－

Summary of Contents for MSD-701UHD




















































































































Search results

Summary of Contents for MSD-701UHD

Reviews:

Related manuals for MSD-701UHD

Brands by name

Popular brands

IDK MSD-701UHD, Command Reference Manual

Search results

Summary of Contents for MSD-701UHD

Reviews:

Related manuals for MSD-701UHD

Brands by name

Popular brands