IDK MSD-6203 Command Reference Manual Download

Page: 79 / 120

MSD-62 series Command Guide

@GCI / @SCI

RS-232C transmission

Getting

Command

@GCI

Response

@GCI, mode

Setting

Command

@SCI, mode

Response

@SCI, mode

Parameter

mode: RS-232C transmission mode

0 = RS-232C transmission mode OFF, 1 = RS-232C transmission mode ON

Getting

example

Command

Response

@GCI

@GCI,0

Description Getting the set RS-232C transmission mode.

Setting the RS-232C transmission mode to OFF.

Setting

example

Command

Response

@SCI,1

Description Setting the RS-232C transmission mode to ON.

Remarks

Once RS-232C transmission mode is set to ON, the RS-232C connector cannot

be used for communication command control from PC to the MSD or for control

command output from the MSD to external devices. Only the command that sets

the RS-232C transmission setting to OFF can be accepted.

Summary of Contents for MSD-6203

























































































































Search results

Summary of Contents for MSD-6203

Reviews:

Related manuals for MSD-6203

Brands by name

Popular brands

IDK MSD-6203, Command Reference Manual

Search results

Summary of Contents for MSD-6203

Reviews:

Related manuals for MSD-6203

Brands by name

Popular brands