ICPDAS IR-712A User Manual Download Page 4

Page: 4 / 38

IR-712A Universal IR Learning Remote Module (Ver. 1.3, Aug/23/2016) 3

1. Introduction

The Intelligent Home and Building Automation are becoming the hot topics recently in

the world. Many countries are devoted to development and promotion in this field.

There are many kinds of consumer electronics and home appliances in the market

applying the IR remote control function because of its mature technology and low cost.

However, these appliances are usually equipped with their own remote controls using

diverse IR protocols which are not unified to a standard. If these IR commands of

different appliances can be collected and integrated to the control interfaces, it is

possible to implement the automation application for a better living experience.

IR-712A is a universal IR learning remote module which can learn IR remote

commands of diverse electronic devices. The learning commands (max. 224) can be

stored in the module or saved to a file. IR-712A supplies 2 IR output channels for

individual or simultaneous control on multiple devices. The accompanied RS-232 and

RS-485 interfaces with Modbus/RTU protocol provide more flexible expansion and

control on the module. Besides, IR-712A software utility provides users with easy

configuration, learning, test and storage of IR commands. As a replacement of IR

remote controls and a module that can be easily integrated with Modbus master
devices (e.g. PAC, PLC, PC… etc.), IR-712A is well-suited for smart home and

building automation.

Figure 1-1

IR-712A application architecture.

Summary of Contents for IR-712A







































Search results

Summary of Contents for IR-712A

Reviews:

Related manuals for IR-712A

Brands by name

Popular brands

ICPDAS IR-712A, User Manual

Search results

Summary of Contents for IR-712A

Reviews:

Related manuals for IR-712A

Brands by name

Popular brands