ICPDAS IR-712A User Manual Download Page 14 | Manualshive

Page: 14 / 38

background image

IR-712A Universal IR Learning Remote Module (Ver. 1.3, Aug/23/2016) 13

2.6 Firmware Update DIP Switch

There is a DIP switch at the lateral of the IR-712A

’s case. It is for the setting of the

firmware update mode. The following explains how to use the DIP switch.

2.6.1 Update Firmware Mode

Push the DIP switch to the

“FW” position as shown in Figure 2-12. The IR-712A will be

in the update firmware mode after cycling the power. Users have to update the
firmware by the RS-232 port of the IR-712.

Figure 2-12

DIP switch in

“FW” position.

To  update  the  firmware,  users  can  click  the  menu  [Tool]  ->  [Update  Firmware  to  IR-
712A]  from  the  IR-712A  Utility  to  launch  the  firmware  update  tool.  Please  follow  the
below  steps to finish the update firmware procedure, which  is also depicted in Figure
2-13.

(1) Click

“COM” radio button and select “COM Port” of the host PC connected to the

RS-232 port of IR-712A.

(2) Click

“Browser” to find the firmware file, e.g. ir712A_vx_xx.fw.

(3) Click

“Firmware Update” button to start the update procedure.

The result of the update would be shown in

“Firmware Update” section.

Note:

1. After updating the firmware, remember to push the switch to

“OP” mode and power

cycle the IR-712A to run in operation mode.

2. Updating Firmware would not change the serial communication settings and IR
commands saved in the IR-712A.

«
...
12
13
14
15
16
...
»

Summary of Contents for IR-712A







































Reviews:

No comments

Related manuals for IR-712A

Brand: Farris Engineering Pages: 12

Brand: Eastern Times Technology Pages: 4

Brand: Vacon Pages: 18

Brand: Van Air Pages: 4

Brand: Case IH Pages: 81

U-verse Advance Series A10

Brand: AT&T Pages: 2

Brand: Goodson Pages: 4

Brand: Moeller Pages: 2

Brand: ApexWaves Pages: 16

ConnectCore 6 Plus

Brand: Digi Pages: 105

Brand: Xylem Pages: 28

Brand: Bardiani Pages: 80

Brand: Overland Storage Pages: 4

Infi 90 IMCPM03

Brand: Bailey Pages: 61

SEPCOM SIP BED Easy

Brand: WAMGROUP Pages: 52

Brand: DH Instruments Pages: 30

Brand: Vag Pages: 19

Brand: Carrier Pages: 86

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands