Iconix IC215S-R User Manual Download Page 65

Page: 65 / 68

ive Users Manual - Models ICL-R & IC215S-R

Sensitivity:

Freq. Range:

Max SPL:

№. Transducers:

Dimensions:

Weight:

Hardware:

Enclosure:

Inputs:

Controls (Rear Mounted):

Computer Controls:

Status Indicators:

Power Connector:

Finish:

Network Digital Format:

PM-2LR AMPLIFIER

Type:

Power Rating:

THD Distortion:

Hum & Noise

:Power Required:

1.4 V (for rated power output)

43 Hz to 100 Hz

133 dB program, 136 dB peak,

Two model SSL15-14, 15” cone woofers, 800 Watts

program at 4 Ohms (each)

44.5” H x 20” W x 24” D (113 cm x 50.8 cm x 61 cm)

206 Lbs (93.4 Kg)

Aeroquip Flytrack, Handles, Casters

Finnish Birch, perforated steel grille

Analog Audio Input 1: Looping XLR (female in, male out)

Analog Audio Input 2: Phoenix 6-pin (looping 3-in, 3-out)

CobraNet: Dual RJ45 connectors (for CAT 5 copper cable)

AES/EBU: Phoenix connector

Power On/Off, Push-To-Reset circuit breakers

Mute button;

Up & Down Output Level push buttons;

10 dB Input pad (on Analog 1 input)

Gain, Mute, On/Standby, Input Selection

Compression,

8-Band Parametric EQ

Shelving & Rolloff Filters

Delay

Power, Signal, Overdrive, Thermal, Mute, Input Pad

Powercon locking connector

Black paint

16, 20 or 24 bit PCM; 48 or 96 kHz sample rat;

Selectable network latency

Class D amplifier/DSP processor

2 x 850 Watts RMS, 950 W Program

< 0.05% typical

<100 dB (A weighted)

90/136 V or 180/260 V AC, 50/60Hz.

13 Amps @ 120 V; 6.5 Amps at 240 V

Idle current; 380 ma @ 120 V; 190 ma @ 240 V

Note:

All analog inputs and outputs comply with AES Standard 45-2005 on interconnecting,grounding and shielding.

IC215S-R Technical Specifications

Summary of Contents for IC215S-R





































































Search results

Summary of Contents for IC215S-R

Reviews:

Related manuals for IC215S-R

Brands by name

Popular brands

Iconix IC215S-R, User Manual

Search results

Summary of Contents for IC215S-R

Reviews:

Related manuals for IC215S-R

Brands by name

Popular brands