Iconix IC215S-R User Manual Download Page 45 | Manualshive

Page: 45 / 68

background image

IC

L

ive Users Manual - Models ICL-R & IC215S-R

45

While you are setting up RHAON’s Preference, you can click on the General tab to review the program’s default settings and change
them if necessary. We already discussed the selection of a Networking Adapter (aka NIC) in the Connect section of this manual. Unless
you are a networking expert you should leave the default settings under SNMP (Simple Network Management Protocol) Variable Re-
trieval alone: SNMP is not as simple as its name implies. IP Addressing is also covered in the Connect section of this manual. After your
network is set up and operating there should be no reason to change these settings.

Change the units of temperature (Fahrenheit or Centigrade) setting to the one that is most useful to you and your fellow operators.

Under Group Settings, you can set up a Power On Sequencing Delay for all grouped loudspeakers. This will help avoid a voltage surge
that can trip building circuit breakers. Depending on the delay interval you select, there will be a .5, 1.0, 1.5 or 2.0 millisecond turn-on
delay between each amplifier in the Group.

Start Up options allow you to always open RHAON in Full Screen mode and to require Sign-In. When the Sign-In option is checked, the
program will ask for your password whenever it is opened.

General Preferences

«
...
43
44
45
46
47
...
»

Summary of Contents for IC215S-R





































































Reviews:

No comments

Related manuals for IC215S-R

Brand: Panasonic Pages: 16

Brand: Watts Pages: 12

Brand: Magnavox Pages: 78

Brand: Harman Kardon Pages: 4

Brand: Velleman Pages: 3

Multi-room system

Brand: Systemline Pages: 22

Brand: Discount Car Stereo Pages: 5

boomSTREAM BTSPK2

Brand: Scosche Pages: 8

Brand: JBL Pages: 28

Brand: ASL INTERCOM Pages: 11

Brand: ADEMCO Pages: 40

Brand: DAPAudio Pages: 8

125.032, 125.063

Brand: Vonyx Pages: 16

Brand: KEF Pages: 6

Brand: Eclipse Pages: 12

Brand: Naxa Pages: 9

Brand: Serenity Pages: 3

Brand: D.A.S. Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands