Iconix IC215S-R User Manual Download Page 38 | Manualshive

Page: 38 / 68

background image

IC

L

ive Users Manual - Models ICL-R & IC215S-R

38

At this point the beam steering changes have not been sent to an associated array or stored as a Preset.

ICL-R arrays can store up to 10 different configurations as Presets in their DSP memory, but beam steering data and other configuration
settings can not be saved as a preset in the Virtual mode. The configuration settings can be saved in the project file, but they can not
loaded into an array until one is connected.

When an array is connected selecting either Write to Device or Save as Preset in the Beam Steering window will allow you to send the
beam steering information to the array. The two commands are in the lower right of the beam steering window. Write to Device will send
the beam steering settings direct to the array’s DSP and write over any previous settings. Save to Preset will store the beam settings in
the designated Preset.

If you attempt to leave Beam Steer-
ing without saving the setup informa-
tion, a prompt will remind you that
you need to save the settings if you
want to keep them.

Note that the Beam Steering module controls only beam steering. EQ, compression, etc. configuration settings are controlled in the Con-
trol Mode.

Same room, only the opening angle of the stacked ICL-R array has been reduced to 5%.

«
...
36
37
38
39
40
...
»

Summary of Contents for IC215S-R





































































Reviews:

No comments

Related manuals for IC215S-R

Brand: Olympia Pages: 5

Brand: Xilica Audio Design Pages: 10

Three-Phase Running Gear

Brand: Miller Electric Pages: 4

Brand: jacarta Pages: 4

Brand: Fender Pages: 56

Brand: FBII Pages: 48

Brand: HAI Pages: 2

Brand: iHome Pages: 12

Brand: iHome Pages: 2

Brand: La Gard Pages: 2

POWER TIG 210EXT

Brand: R-Tech Pages: 27

Brand: Veeder-Root Pages: 699

Brand: Niles Pages: 2

Brand: Technics Pages: 44

Brand: Skytec Pages: 12

NeuroKom IP DS 935-SH

Brand: Gehrke Pages: 8

Brand: QFX Pages: 6

SOUNDPOINT SP5II

Brand: JBL Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands