background image

R

WARNING! NEVER 

hold the transceiver so that the

antenna is very close to, or touching exposed parts of the
body, especially the face or eyes, while transmitting. The
transceiver will perform best if the microphone is 5 to 10 cm
(2 to 4 in) away from the lips and the transceiver is vertical.

R

WARNING! NEVER 

operate the transceiver with a

headset or other audio accessories at high volume levels.
Hearing experts advise against continuous high volume op-
eration. If you experience a ringing in your ears, reduce the
volume level or discontinue use.

NEVER

connect the transceiver to an AC outlet or to a

power source of more than 16 V DC. Such a connection will
damage the transceiver.

NEVER

connect the transceiver to a power source that is DC

fused at more than 5 A. Accidental reverse connection will be
protected by this fuse, higher fuse values will not give any pro-
tection against such accidents and the transceiver will be ruined.

NEVER

attempt to charge alkaline or dry cell batteries. Be-

ware that external DC power connections will charge batteries
inside the battery case. This will damage not only the battery
case but also the transceiver.

i

IMPORTANT

READ ALL INSTRUCTIONS carefully and completely before
using the transceiver.

SAVE THIS INSTRUCTION MANUAL—This instruction man-
ual contains important operating instructions for the IC-T7H.

EXPLICIT DEFINITIONS

The explicit definitions below apply to this instruction manual.

CAUTIONS

WORD

DEFINITION

R

WARNING

Personal injury, fire hazard or electric shock
may occur.

CAUTION

Equipment damage may occur.

NOTE

If disregarded, inconvenience only. No risk
of personal injury, fire or electric shock.

The IC-T7H complies with essential requirements of the
89/336/EEC directive for Electromagnetic Compatibility.
This compliance is based on conformity with the ETSI
specification ETS300 684 (EMC product standard for
Commercially Available Amateur Radio Equipment).

Summary of Contents for IC-T7H





































Reviews: